Synchronous Machines Trainer Kit Model ELTR 030
Home » Products » Synchronous Machines Trainer Kit Model ELTR 030
Synchronous Machines Trainer Kit Model ELTR 030
TEST RACK/INSTRUMENTATION
A] Aluminum profile sturdy flat panel (table top) system, carrying various high voltage components housed in plastic enclosures (panel) to minimize shock possibility.
– Input 3 phase DOL Starter panel (EMT1)
[10 Shrouded Banana]
– 4 pole MCB of 415 V/2A .
– DOL 9A Contactor with 230V / 50 Hz / 11VA COIL .
– Bimetallic thermal O/L relay with range 1.4A – 2.3A .
Integrated AC (3/1 phase) measurement panel EMT34 Bidirectional optionally with PC interface & multifunction power meter EMT20F [1 phase]
Item Description
– Consist of 2 nos of (96X96mm) Digital meters one each for 3ø & 1ø. Measures V, I, PF (0.2 lag – unity 0.2 lead), Hz. Hence separate analog watt-meters (3, 1) are not needed.
– Current specs for 3 meter = 1.5A (Balanced load) and 1A/5A for 1ø meter (170-250V).
Technical Specifications
– FWD/REV, Star-Delta starter panel (EMT 4)
[12 Shrouded Banana]
– FWD/REV, 3 pole 3 way switch with center OFF, 6A/440V.
– Star/Delta switch 3 pole, 3 way with center OFF, 6A/440V.
– 3 Phase wound Rotor & Sync. Motor panel (EMT 5A/5B)
[8 Shrouded Banana]
– Rotor resistors of 30E/5A with 3 taps of 0E, 15E, 21E, 30E each ——–3 nos
– Rotor resistor selector switch, 3 pole.6 Way .6A/440 V.
– DC Rotor excitation over current relay (3Amp)
– 1ø Motor, Alternator & Sync. Motor Panel (EMT 16)
[14 Shrouded Banana]
– 1ø MCBs of 4A/1.6A 1 each.
– 2no 2P2W selector switches to run as 1ø alternator then as synchronous motor.
– 8A pushbutton switch to simulate as centrifugal switch.
– DC voltmeter and DC ammeter panel (EMT 6A/6B)
[14 Shrouded Banana]
a) DC voltmeter (0-300V)
b) DC Ammeter (0-5A) with polarity protection diode
c) Field failure relay to control Armature supply. Both 6A/6B needed simultaneously.
– SCR Actuator (variable DC) cum sensor signal conditioning panel (EMT9) [4 Shrouded Banana]
– Full bridge SCR based 0V-195V / 5 Amp cosine firing with linear charateristics.
– Supports signal conditioning circuit for speed, torque in kg wt to output 0-2.5Vdc (FS).
– 3 Nos. of these supplies required for DC Armature, DC motor field and AC generator field.
– Instrumentation Power supply cum Multichannel DPM panel (EMT 8)
[10 Shrouded Banana]
(a) +/-12 V, 500 mA (b) +5V, 300mA (c) Unregulated 17V dc/750 mA
(d) line synchronizing signal. (e) 13V / 3 Amp. (f) Multi channel DPM for digital display of torque, speed etc
– Resistor Load (EMT14A/14B)
(1) AC Resistors = 10K/5K/3.5K/2.5K/2K/1.5K/200WX3 phases/ 6 taps
(2) DC Resistors = 750E/600E/300E/212E/162E/125E/112E/100E/400W / 6 taps+OFF+ separate 60E tap for DC series Gen.
– LC Load (EMT 15A/15B) panel
(A) Inductive load = 0.15H/0.3H/0.45H/0.6H/0.75H/1.5H/3H/400mAX3Nos.
(B) Capacitive load =1.25μ/2.5μ/5μ/415VX 3Nos.
– Mechanical Dimension(mm) : = 1170(L) X 300 (W) X 990 (H)
– Net Weight : 56 kg
– Optional Accessories :
(1) Hand held non contact Digital tachometer
(2) Analog AC voltmeter (EMT2) and dual range Ammeter (EMT3)
(3) EMT 34 bidirectional power meter and analyser with RS232C / RS485
(4) 3 phase sequence indicatorcum protection panel (P30)
(5) 1 phase variable transformer 3 Amp rating
See also different:
Sci-tech Inverted Pendulum Apparatus Model MT 115’s learning contents of the experimental unit are extended by ‘Controller Unit’ that is more complex because of its two independent drives. Conducting the experiment makes high demands on the sy [...]