Technical Specifications

The trainer has the following specifications:

Residential Switches:

1. Mounted on Plexiglas s panels with 4mm terminals
2. Switch , surface mount, 2 way, 2 terminal, 10A , 1gang (4 modules)
3. Switch, surface mount, 2 way, 3 terminals, 10A, 1 gang (4 modules)
4. Switch, surface mount, 2 way, 4 terminals, 10A, 1 gang (4 modules)
5. Switch, surface mount, 2 way, Intermediate, 10A, 1 gang (4 modules)
6. Switch, surface mount, 1 way, 2 terminals, 10A, 2 gang (2 modules)
7. Switch, surface mount, 2 way, 3 terminals, 10A, 2 gang (2 modules)
8. Switch, surface mount, 2 way, 4 terminals, 10A, 2 gang (2 modules)
9. Switch, surface mount  marked “Bell” (2 modules)
10. Switch, surface mount,  illuminated  (2 modules)
11. Switch, surface mount,  dimmer  (2 modules)
12. Switch, ceiling pull type, 1way, 3 terminal, 10A (2 modules)
13. Bell/Door opener push button: (1 module)
14. 2 SPST switches 250 VAC, 110A

Sockets Sets:

The sockets are mounted onto plexiglass  panel with 4mm terminals, each socket includes a matching plug.

1. 1 Phase socket with switch , 13A, 3 prong, 1gang (3 modules)
2. 1 Phase socket with switch , 13A, 3 prong, 2gang (2 modules)
3. 1 phase socket ,Shuko Type, 16A, 1 gang (5 modules)
4. 1 phase industrial Socket , with cover, 16A, 2Pole & Earth (2 modules)
5. 3 phase industrial socket , with cover, 16A ,2Pole with Neutral & Earth (2 modules)
6. 1 phase CEE ,16A, 3 Round Prong (2 modules)

Industrial switches:

1. Toggle switches , 2PST (4 modules)
2. Push Button,1 NO 1NC (2 modules)
3. Cam Switches, ON /OFF (2 modules)
4. Selector switch, (for three phase amperage measurement)(1 module)
5. Selector switch (for three phase voltage measurement) (1 module)
6. Stepping relay for sequencing : 2SPST switches with 4 sequences (1 module)
7. Latching relay:(1modules)
8. 2 relay with Bistable operating contacts, coil,
9. 24 VAC, 3 contacts, 48VAC, 2A

Circuit Breakers:

1. MCB,1 phase, 6A (5 modules)
2. MCB,1 phase, 16A (2 modules)
3. MCB,3 phase, 16A (1 module)
4. ELCB,1 phase (1 module)
5. ELCB,3 phase (1 module)
6. NFB,1 phase (1 module)

Lights and Fixtures:

It includes match lamp holders complete with lamps mounted on to plexiglass panels with 4mm terminals,

1. Incandescent lamp holder with bulb ,E27,220V (4modules)
2. Incandescent lamp holder with bulb ,E14,220V (4modules)
3. Fluorescent lamp holder with starter and ballast,10W (2modules)
4. Fluorescent lamp holder with starter and ballast, 20W (2modules)
5. Mercury lamp holder with lamp (2 modules)
6. Pilot signalling lights, 24VAC, (1modules)
7. Set of three (red, yellow, green)
8. Filament tungsten lamp
9. tungsten filament lamp
10. Metal Halide lamp
11. High pressure sodium lamp
12. Low pressure sodium lamp

Controls and Components:

1. Control transformer, input 220 VAC, output 6/12/24 (2 modules)
2. Control relay : 24 VAC, 2NO 2NC (2 modules)
3. Control relay : 220VAC, (2 modules)
4. Timer : 24hours 2NO 2NC (1 module)
5. Door Bell, 12VAC (1module)
6. Buzzer ,12VAC (1module)

Measuring Instruments:

1. Mains input panel for Single and Three phase (1 module)
2. Set of stackable 4mm connection test leads (set)
3. Test leads stands of stackable cable (One)
4. Ampere meter :0 to 20 Amps (1 module)
5. Voltmeter : 0 to 500VAC (1 module)
6. Ampere meter : 0-5 Amps (1module)

Telephone/Intercom Modules:

1. Door phone signalling board (1 module)
2. Master phone / Intercom (2 rooms + door station + buzzer) (1 module)
3. Substation phone / Intercom (2 modules)
4. Signalling push button (maid / porter / valet) (1 module)
5. Electric door lock 12V(1 module)

Training Panel Frames:

1. Three Level Mobile Frames with 4 rails (1 module)
2. Height : 1850mm , Width : 1100mm

Optional:

HIGH VOLTAGE NEON LAMP TEST TRAINER

TECHNICAL SPECIFICATION

• Fireman Switch: AC230V, 50Hz, 2 Pole
• MCB: 10A, AC230V, 50Hz, 2 Pole
• Timer: Pre-set Time to Switch On/Off for the Electrical Appliances, Quartz, with supply failure reserve at 20°C, 200h after being connected for 120 h, Max. Power With Incandescent Lamp – 1000W, IP 30, 24hrs Operation Cycle, 1 Changeover Switch, According to Standard EN 60730-2-7
• Switch: 1Gang, 1 Way, 20A , 230V, 50Hz, 2 Pole
• Transformer Rated Input Power(<VA): 450W, AC 230V, 2A, 50Hz
• Transformer Rated Output Power(KVA): 450W, AC 15kV, 30mA, 50Hz
• Neon Lamp: Dia. 10mm with wording

Additional Items:

1. Additional meters to enhance the measurement capabilities
2. Storage Cabinets are available for safe and secure storage of the Panel Modules.
3. Double Door Storage cabinet with slots to accommodate the panels (Optional)

Electronic Fault insertion system:

1. Multiple electronic fault insertion system :

This system allows for multiple faults to be inserted at any one time. Faults can be inserted individually or in groups

1. Circuit block diagram electronic fault display panel :

Features electronic schematic block diagram with faults indicated by LEDs. When the fault is electronically activated a corresponding LED will illuminate showing the fault is active.

1. Student Testing Mode :

The LED fault indication display can be deactivated so that the faults can be active but the display can be switched Off

1. Electronic Fault Reset Button :

The LED control should have a fault-reset button that will clear and reset  the system back to normal.

1. Test Points :

The trainer has short circuit protected test points that allow the student to take measurements during the troubleshooting exercises.

Extra Accessories (Optional):

• 5 Digit Digital Multi-meters
• Digital Lux Meter