DIGITAL LOGIC CONTROL TRAINER MODEL SCI-DTK01A
DIGITAL LOGIC CONTROL TRAINER MODEL SCI-DTK01A
Aesthetically designed injection moulded electronic desk (Master unit) with common experiment resources like Power supplies, Function Generator, switches, indicators, DPM etc. while the slot will carry replaceable expt. Panels 4 mm sockets in a arranged on a grid of 19 x19mm to receive plug in components
Item Description
- Optionally computer assisted Training through use of Lab view® based executables supported by variety of
virtual instrumentation like toggle switches, leds etc. - Emphasis on troubleshooting skills through fault switches.
- Replaceable panel connects to computer I/F on master unit through 64 pin (Euro connector)
- Set of Users Guide provided with each trainer
Technical Specifications
Power Supply:
DC Supply – +5V / 1A. & ±12V, 500mA
3 to 18V DC (Variable)/ 1A (Isolated) -2 nos. With short ckt & overload protection.
Both kept isolated to facilitate either 3 to 36V or +18Vpower supplies etc.
AC Supply – 12-0-12V AC, 150mA. Short circuit protected
Function Generator
Waveform – Sine, Triangle & TTL O/Ps
Frequency – 1 Hz to 1MHz in 6 ranges, with amplitude & frequency control pots.
Voltage & current – 15V p-p max. (Sin / TRG) open ckt. (7.5Vpp into 50 ohm termination)
3-Phase voltage Generator – 6Vrms/50Hz,/120 degree phase shifted 3 O/ps, max 10mA loading
Logic input switches & status Indicators – Bi-Colour buffered LED status indicators 8X2 nos for High/Low indication. Input Data Switches (Slide switches x 8nos.)
Computer Interface –
Digital – I/O Using parallel port or optional USB port (through converter supplied)8 I/p, 8 O/P, 8
Bidirectional I/O Lines (TTL), opto isolated Adaptor to prevent damage to pc
Analog – I/P 2nos. of +9V ADC channels 2nos. of 0-2.5V ADC channels, Max BW-1KHz
Analog – O/P O/p 0-10V max (optionally 0-2.5V), max. load 10 mA
Pulsar switches (2no.) – with four debounced outputs (TTL), A, A, B, B
Logic probe – to detect High/Low, level TTL pulses upto 1MHz, with bi-colour LEDs to indicate status.
7 segment display – 2-digit red led 7 segment with built in BCD to 7 segment decoder(TTL)
Onboard DPM (1no.) – provided with mode/range selection, DC volt – 2V/20V & DC current – 2mA/200mA
Mic Pre- Amplifier (optional) – Dynamic mic with preamplifier
Mechanical Dimensions:
(A) Master Unit : 460mm(W), 160mm(H),
350mm(D)
Net weight: 9 Kg. Gross Wt: 11 Kg.
(B) Panel: 439mm x 209mm
L/S Amplifier & speaker (optional) –
Amplifier gain 20, With volume control8ohm, 0.5W, Mounted on hind Plate
Onboard POTS – 1K,1M (Optional in place of counter module)
Fault Switches – 14 nos. of gnd referred fault switches
hidden under replaceable expt. panel on pcb carrying Euro connectors
Accessories – 1) Parallel Port 25pin cable.
2) USB I/O module (optional) with type A to mini B cable
3) Virtual Lab CD
Operating Voltage – 220/240Vac switch settable +/- 10%, 50Hz/80VA
See also different:
Aesthetically designed injection moulded electronic desk. Master unit carrying useful experiment resources like Power supplies, DPMs, Computer Interface, Bar graph LED indicator Function Generator etc. while the central slot will carry replace [...]
